Cat C18 ACERT Propulsion Engine (Tier 3)
Power Rating
- Power Range
-
469-1001 bhp (350-747 bkW)
Engine Specifications
- Speed Range
-
1800-2300 rpm
- Emissions
-
EPA Tier 3 Commercial, IMO II, EU IW
- Aspiration
-
TA, TTA
- Bore
-
5.7in
- Stroke
-
7.2in
- Displacement
-
1106inĀ³
- Rotation from Flywheel End
-
Counterclockwise
- Configuration
-
In-line 6, 4-Stroke-Cycle Diesel
Dimensions & Weights
- Minimum Dry Weight
-
4000lb
- Minimum Length
-
73in
- Maximum Length
-
76in
- Minimum Height
-
47.2in
- Maximum Height
-
51.2in
- Minimum Width
-
44.6in
- Maximum Width
-
47.4in
Standard Equipment:
-
- Air Inlet System
-
- Separate circuit after-cooled (SCAC)
- Open Crankcase Ventilation (OCV) system
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
-
- Cooling System
-
- Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
- Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
- SCAC pump, gear driven, for HEX cooled engines only
- Jacket water pump, gear driven
- Sea water pump, bronze impeller, gear driven
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
-
- Exhaust System
-
- Water-cooled exhaust manifold & turbocharger
- 152 mm (6 in) round flanged outlet
-
- Flywheels & Flywheel Housings
-
- Flywheel Housing, SAE No. 0
- Flywheel, 18 inch, 136 teeth
- SAE standard rotation
- SAE No. 1, Flywheel: 14 inch, 113 teeth
-
- Fuel System
-
- Front service simplex fuel system
- Fuel transfer pump, gear driven
- Manual fuel priming pump
- Hybrid fuel line design
-
- Lube System
-
- Front service simplex oil system
- Center sump oil pan:
- Front and top service oil filler locations
- Front service dipstick
- Oil pump, gear driven
-
- Mounting System
-
- Front support - adjustable
-
- Power Take-offs
-
- Poly-V groove for alternator drive
- NOTE: There are no standard power take-offs available
-
- General
-
- Front damper guard
- Front service engine
- Common electrical bonding point
- Engine does not ship with zinc components
- Engine is certified to D2/E2 emissions cycles
- CERTIFIED TO EU STAGE IIIA AND CCNR STAGE II (E3 CYCLE) EMISSIONS STANDARDS.
-
- Control System
-
- Programmable low idle
- WOSR (Wide Operating Speed Range) available for EPA Tier 3 - B and C Ratings
- Adjustable High Idle (TEL) - EPA Tier 3 WOSR Ratings Only
- Electronic diagnostics and fault logging
- Engine and transmission monitoring (speed, temperature, pressure)
- Electronic fuel/air ratio contro
- Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
- Torque Limiting functionality for WOSR ratings only
- 70-pin customer connector
- Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA +/-
Optional Equipment:
-
- Exhaust System
-
- Dry Elbows
- Water-Cooled Elbows
- Flexible Fitting
- Flange
- Muffler
- Muffler Spark Arresting
-
- Air Inlet System
-
-
- Charging System
-
- Battery Chargers
- Charging Alternators
- Alternator Mounting Group
- Ammeter
-
- Control System
-
- MECP I
- CATERPILLAR ALARM AND PROTECTION
-
- Cooling System
-
- AUX EXPANSION TANK FLANGE KIT
-
- Fuel System
-
- Duplex Fuel Filters
- Flexible Fuel Lines
- Fuel Cooler
- Primary Fuel Filters
-
- Instrumentation
-
- Instrument Panels
- OEM Wiring Harness
- Engine to Engine Harness
- Gauges
- Transmission Sensors
- Oil Level Sensor
-
- Lube System
-
- Duplex Oil Filters
- Transmission Oil Cooler
- Sump Pump
-
- Mounting System
-
- Vibration Isolators
- Front Support
- Rear Support
-
- Power Take-offs
-
- NOTE: PTO OPTIONS REQUIRE TORSIONAL VIBRATION ANALYSIS
- Crankshaft Pulleys
- Front Stub Shaft
- Hydraulic Pump Drive Adapter
- Front Enclosed Clutch
-
- Protection System
-
- Marine Classification Society and SOLAS
- Marine Classification Society and Fire Resistance
-
- Starting System
-
- STARTING SYSTEM Electric Starting Motors - Single 24 Volt
- Air Starting Motor
- Air Start Accessories
- Starting Aids - JW Heaters
- Battery Sets - 24 Volt - Dry
-
- Packing
-
- Engine Protective Cover
- Storage Preservation
- Export Packing